PIC18F47J13-I/ML【PDF 28/71 页】IC PIC MCU 128KB FLASH 44QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3844

24页 25页 26页 27页 [28页]29页 30页 31页 32页

PIC18(L)F2X/4XK22

DS41412E-page 34

2010-2012 Microchip Technology Inc.

2.4

Clock Source Modes

Clock Source modes can be classified as external or

internal.

External Clock modes rely on external circuitry for

the clock source. Examples are: Clock modules

(EC mode), quartz crystal resonators or ceramic

resonators (LP, XT and HS modes) and Resistor-

Capacitor (RC mode) circuits.

Internal clock sources are contained internally

within the Oscillator block. The Oscillator block

has three internal oscillators: the 16 MHz High-

Frequency Internal Oscillator (HFINTOSC),

500 kHz Medium-Frequency Internal Oscillator

(MFINTOSC) and the 31.25 kHz Low-Frequency

Internal Oscillator (LFINTOSC).

The system clock can be selected between external or

internal clock sources via the System Clock Select

(SCS<1:0>) bits of the OSCCON register. See

Section 2.11

“Clock

Switching”

for

additional

information.

2.5

External Clock Modes

2.5.1

OSCILLATOR START-UP TIMER (OST)

When the oscillator module is configured for LP, XT or

HS modes, the Oscillator Start-up Timer (OST) counts

1024 oscillations from OSC1. This occurs following a

Power-on Reset (POR) and when the Power-up Timer

(PWRT) has expired (if configured), or a wake-up from

Sleep. During this time, the program counter does not

increment and program execution is suspended. The

OST ensures that the oscillator circuit, using a quartz

crystal resonator or ceramic resonator, has started and

is providing a stable system clock to the oscillator

module. When switching between clock sources, a

delay is required to allow the new clock to stabilize.

These oscillator delays are shown in Table 2-2.

In order to minimize latency between external oscillator

start-up and code execution, the Two-Speed Clock

Start-up mode can be selected (see Section 2.12

“Two-Speed Clock Start-up Mode”).

TABLE 2-2:

OSCILLATOR DELAY EXAMPLES

2.5.2

EC MODE

The External Clock (EC) mode allows an externally

generated logic level as the system clock source. When

operating in this mode, an external clock source is

connected to the OSC1 input and the OSC2 is available

for general purpose I/O. Figure 2-5 shows the pin

connections for EC mode.

The External Clock (EC) offers different power modes,

Low Power (ECLP), Medium Power (ECMP) and High

Power (ECHP), selectable by the FOSC<3:0> bits.

Each mode is best suited for a certain range of

frequencies. The ranges are:

ECLP – below 500 kHz

ECMP – between 500 kHz and 16 MHz

ECHP – above 16 MHz

The Oscillator Start-up Timer (OST) is disabled when

EC mode is selected. Therefore, there is no delay in

operation after a Power-on Reset (POR) or wake-up

from Sleep. Because the PIC MCU design is fully

static, stopping the external clock input will have the

effect of halting the device while leaving all data intact.

Upon restarting the external clock, the device will

resume operation as if no time had elapsed.

FIGURE 2-5:

EXTERNAL CLOCK (EC)

MODE OPERATION

Switch From

Switch To

Frequency

Oscillator Delay

Sleep/POR

LFINTOSC

MFINTOSC

HFINTOSC

31.25 kHz

31.25 kHz to 500 kHz

31.25 kHz to 16 MHz

Oscillator Warm-Up Delay (TWARM)

Sleep/POR

EC, RC

DC – 64 MHz

2 instruction cycles

LFINTOSC (31.25 kHz)

EC, RC

DC – 64 MHz

1 cycle of each

Sleep/POR

LP, XT, HS

32 kHz to 40 MHz

1024 Clock Cycles (OST)

Sleep/POR

4xPLL

32 MHz to 64 MHz

1024 Clock Cycles (OST) + 2 ms

LFINTOSC (31.25 kHz)

LFINTOSC

HFINTOSC

31.25 kHz to 16 MHz

s (approx.)

OSC1/CLKIN

OSC2/CLKOUT(1)

I/O

Clock from

Ext. System

PIC MCU

Note

Alternate pin functions are listed in

Section 1.0 “Device Overview”.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式